3D Printer - Tapadás segítők - 3D Printer - FDM (szálas)

3Dlac 400ml - megakadályozza a nyomat deformációját az üvegasztalon

GLUE-3DLAC

3Dlac 400ml inélkülözhetetlen eszköz nagyobb tárgaz vagy zsugorodó anyagoknál a nyomatok üveg asztalon atrtásához.

Minnél magasabb az asztal hőfok, annál jobban tapad (60 fok alatt hatástalan és elengedi a tárgyat)

Vízzel oldható igy könnyen tisztítható az asztalról.

The different temperature of the print bed translates into different adhesion levels:

Below 60 ° C: no adhesion, objects can be detached from the plate.
60 - 75ºC: medium adherence, for simple geometries.
75 - 95ºC: high adherence, for complex geometries and long prints.
Above 95ºC: Very high adherence, for very complex geometries and very long prints.

How to use 3Dlac 400ml:

Clean your 3D printer build plate
Make sure that the print bed temperature is below 50ºC
Spray 3Dlac 400ml on the print bed (use a well-ventilated area)
First warm up your print bed and then print
After printing, wait for the build plate to cool down
Your printed object will easily peels off

Spray is fully soluble in water, so cleaning the build plate is an easy process.

Bruttó: 4 445 Ft

Egységár: Bruttó: 11 113 Ft/kg

Kosárba

Részletek

Capton tape - 20mm x 30m

CAPTON-20mm

Bruttó: 3 810 Ft

Kosárba

Részletek

Capton tape - 20cm x 30m

CAPTON-200mm

Szélesség

Bruttó: 12 700 Ft

Kosárba

Részletek

Magigoo PA glue stick - 50ml

MAGIGOO-PA

Ideal for: PA - NYLON

MAGIGOO PA is designed for professional use, to work exclusively with Polyamide filaments. The part should be relatively easy to remove once it cools and the glue residue should also be easily cleaned off.

Nylon filaments prove to be challenging materials for FDM printing due to their lower adhesion to conventional 3D-printing build surfaces and their higher tendency to warp. Furthermore, there are several classes of PA filaments each behaving differently. MAGIGOO-PA is a specialized solution for FDM printing of PA filaments which was developed to work with a wide number of PA types.

HOW TO USE IT?
MAGIGOO PA has been designed and tested to work with different PA and fibre reinforced filament brands.
• Shake the bottle.
• Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
• Print according to the filament/printer manufacturers recommendations
• Allow to cool and Remove. The print should pop right off
• Clean - Use a damp cloth to wipe off.

SAFETY:
Using this product with other than PA type filaments might cause over adhesion and damage your build surface.
Tips:
For larger prints a 20 mm brim is recommended
In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier

Bruttó: 12 700 Ft

Kosárba

Részletek

Magigoo Original - 50ml

MAGIGOO-ORIG

All you need for sure adhesion of 3D prints.

Magigoo is an easy to use 3D printing adhesive designed to address ‘the first layer not sticking problem’. A strong adhesion between the 3D print and the heated build plate is ensured when applying Magigoo.
However the actual magic starts when printing is ready: just wait for the plate to cool down and then remove your prints with just a finger flick!
In addition, Magigoo helps to prevent warping. Isn’t it magic? Regardless of you being a hobbyist or professional – it is extremely rewarding to have a 30 hour print complete without any warping and having it release easily once cooled.

Over 100 applications
ABS, PLA, PETG, HIPS, ASA, TPU
Easy application
Easy release
Easy clean
No smell
Non-toxic
No additional tools needed
Easy to transport
Nicer print finish

Bruttó: 11 430 Ft

Kosárba

Részletek

Magigoo PC glue stick - 50ml

MAGIGOO-PC

Ideal for: PC, PC/ABS , ABS

MAGIGOO PC is designed to work exclusively with polycarbonate type filaments. This adhesive for professional use makes sure prints stick firmly when the print-bed is hot and that the part is easy to remove once it cools. This unique and innovative mechanism means that no tools are needed to remove prints from the bed. They just pop off when the bed cools down.

The strength and toughness of PC make it an ideal FDM material for the production of functional prototypes as well as end use part, nonetheless the material does present some printing challenges. Virgin PC has a high glass transition temperature (Tg) and thus can be used in high temperature applications. However, having a high Tg can make it very difficult to print using desktop printers, as these are usually not equipped to cater for the high printing temperatures required to print virgin PC. Virgin PC in fact tends to warp considerably when printed at an insufficient bed temperature (<130 ºC), in non-heated enclosed chambers without the use of an appropriate bed adhesive. Certain manufacturers have improved the printability of PC by the use of plasticizers or blending with other materials. Nonetheless when using these solutions some difficulties are still encountered, firstly with adhesion especially on larger parts still can be an issue. In addition to this some bed adhesion sheets have been proposed to avoid the warp encountered in larger prints, but in this case there is a high tendency that the adhesion sheet being used fuses irreversibly to the print. This means that the expensive sheet needs to be removed very often and also incurs a lot of post processing and cleaning. Magigoo PC can be used on glass or multiple other surfaces. Use on other plastic based surfaces, including sheets is recommended to provide strong adhesion and preventing the part to fuse to the sheet.

HOW TO USE IT:
MAGIGOO PC has been designed and tested to work with different PC filament brands. As the composition of each plastic is a little different, the ideal settings for MAGIGOO PC may vary.

• Shake the bottle.
• Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
• Print according to the filament/printer manufacturers recommendations
• Allow to cool and Remove. The print should pop right off
• Clean - Use a damp cloth to wipe off.

SAFETY:
Using this product with other than PC type filaments might cause over adhesion and damage your build surface.

Tips:
For larger prints a 20 mm brim with multiple layers is recommended.
In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier.

Bruttó: 12 700 Ft

Kosárba

Részletek

Magigoo HT glue stick - 50ml

MAGIGOO-HT

Ideal for: PEI, PEEK, PPS, all HT product over 300 °C

MAGIGOO HT is designed for professional use, to work at high printing temperatures. The part should be relatively easy to remove once it cools and the glue residue should also be easily cleaned off.

High-temperature filaments prove to be challenging materials for FDM printing due to their higher tendency to warp. These materials are generally printed at elevated temperatures owing to their high-temperature properties. MAGIGOO HT is a specialized solution for FDM printing of PEEK filaments which was developed to work at elevated printing temperatures.

HOW TO USE IT:
MAGIGOO HT has been designed and tested to work with build-plate temperature of 150 °C or lower.
• Shake the bottle.
• Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
• Print according to the filament/printer manufacturers recommendations
• Allow to cool and remove. The print should pop right off
• Clean - Use a damp cloth to wipe off.

Using this product with other than PEEK filaments might cause over adhesion and damage your build surface. Follow the instructions found in the technical data sheet for the best results.

Tips:
For larger prints, a 20 mm brim is recommended.
Magigoo HT was designed for glass surface but also works on high-temperature garolite and other build-surfaces.

Bruttó: 22 860 Ft

Kosárba

Részletek

Magigoo TPE,TPC glue stick - 50ml

MAGIGOO-FLEX

WHAT: Magigoo Pro Flex is designed for professional use, to work exclusively with TPU (thermoplastic polyurethane), TPE (thermoplastic elastomer and TPC (thermoplastic copolyester) filaments. The part should be relatively easy to remove once it cools and the glue residue should also be easily cleaned off.

WHY:

TPUs, TPEs/TPCs describe a group of polymers which are sometimes referred to as thermoplastic rubbers. Thermoplastic rubbers exist as co-polymers or a polymer blend, generally of a plastic and a rubber. This imparts both thermoplastic and elastomeric properties. As a result these materials have the advantage of being able to stretch to moderate elongations and returning to the original shape.

Additionally these materials have very good thermal properties, material stability, chemical resistance, and are more cost effective to produce. As a result these materials are highly sought in industrial applications.

Some flexible filaments show lower adhesion to conventional 3D-printing build surfaces and a high tendency to warp. Others tend to stick too well to bare 3D printing surfaces such as glass and PEI. Magigoo Pro Flex is a specialized solution for FDM printing of flexible filaments which was developed to work with a wide number of flexible filament types. Magigoo Pro Flex acts as an intermediate layer between the build-plate and the printed part enabling good adhesion and facilitating print removal as required.

HOW:

Magigoo Pro Flex has been designed and tested to work with different flexible filament brands.

Shake the bottle.
Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
Print according to the filament/printer manufacturers recommendations
Allow to cool and Remove. The print should pop right off
Clean - Use a damp cloth to wipe off.

SAFETY:

Using this product with other than Flexible type filaments might cause over adhesion and damage your build surface.

Tips:

For larger prints and filaments with a high shrinkage rate, a 20 mm brim is recommended.

In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier.

Bruttó: 12 700 Ft

Kosárba

Részletek